Hp Printer 8710 Error Continuous Ink System

Z7_3054ICK0KGTE30AQO5O3KA30N0

hp-concentra-wrapper-portlet

Actions

HP OfficeJet Printers - Resolving 'Print System Problem', 'Problem with Ink System' Errors

This document is for HP OfficeJet 251dw, 276dw, 3610, 3620, 6100, 6600, 6700, 7110, 7510, 7610, 7612, 8100, 8600, 8610, 8615, 8616, 8620, 8625, 8630, 8640, 8660 9010, 9012, 9013, 9014, 9015, 9016, 9018, 9019, 9020, 9022, 9023, 9025, 9026, 9028, and 9012 printers.

The printer does not print, and one of the following error messages displays on the computer or printer control panel.

  • Print System Problem

  • Problem with Ink System

  • Problem with Printer System

Step 1: Check the ink cartridges for leaks

Replace any ink cartridges that leak.

caution:

Do not use leaking ink cartridges.

To find your cartridge number and to purchase ink or toner supplies, go to HP Store or a local retailer. Make sure you are using the correct genuine HP ink or toner supplies for your printer. HP cannot guarantee the quality or reliability of non-HP cartridges or refilled HP cartridges. To check the authenticity of your cartridges, go to the HP anti-counterfeit webpage (in English).

If you have a defective cartridge or printhead, it might be under warranty. To check the warranty on your ink or toner supplies, go to Printer and Page Yield Overview, and then review the limited warranty information for your supplies.

  1. Open the door to access to the ink cartridges.

  2. Wait until the carriage stops moving before you continue.

  3. Remove an ink cartridge, and then inspect the ink cartridge for leaking ink.

    Removing an ink cartridge

  4. If the ink cartridge leaks, replace the ink cartridge. If the ink cartridge is not leaking, insert the ink cartridge into its slot.

    Inserting an ink cartridge.

  5. Repeat these steps for the other three ink cartridges.

  6. Close the ink cartridge access door.

If the error message persists, continue to the next step.

Step 2: Reset the printer

Resetting the printer might clear the error message.

  1. With the printer turned on, disconnect the power cord from the printer.

  2. Unplug the power cord from the power source.

  3. Wait 60 seconds.

  4. Reconnect the power cord to a wall outlet and to the printer.

    note:

    HP recommends plugging the printer directly into a wall outlet.

If the error message persists, continue to the next step.

Step 3: Check the carriage for a printhead latch

Open the door to access to the ink cartridges, and then determine if the carriage inside the printer has a printhead latch.

Example of a carriage with a latch

Image of carriage with a printhead latch

  • If your carriage has a printhead latch, continue to the next step.

  • If your carriage does not have a printhead latch, skip to Service the printer.

Step 4: Reseat the printhead up to three times

To clear the error message, you might need to reseat the printhead up to three times.

  1. Open the door to access to the ink cartridges.

  2. Wait until the carriage stops moving before you continue.

  3. Unplug the power cord from the rear of the printer.

    warning:

    You must disconnect the power cord before reaching inside the printer.

  4. Lift the carriage latch, slightly lift the printhead, lower the printhead back into the carriage, wiggle the printhead left and right, and then lower the carriage latch to lock the printhead into place.

    Animation showing how to reseat the printhead in the carriage

  5. Close the ink cartridge access door.

  6. Reconnect the power cord to the rear of the printer, and then check the control panel for the error message.

  7. Sometimes error messages persist after inserting the printhead. If the error message persists, repeat the steps to reseat the printhead up to three times.

If the error message persists, continue to the next step.

Step 5: Replace the printhead

If the previous troubleshooting steps did not resolve the issue, order a new printhead for replacement.

If you have a defective cartridge or printhead, it might be under warranty. To check the warranty on your ink or toner supplies, go to Printer and Page Yield Overview, and then review the limited warranty information for your supplies.

If your printhead assembly is no longer under warranty, you might be able to purchase a new one online.

  1. If you are in Asia Pacific, the site directs you to a service center in your area.

  2. Search HP Parts Store for your printhead part number. Refer to the following table to find your printhead part number based on the ink cartridge numbers your printer uses.

    Ink cartridge Number

    Country/Region

    Printhead Part Number

    HP 950, 951

    Americas

    CR322A

    Europe, Middle East, Africa

    CR324A

    Asia Pacific, Japan

    CR326A

    HP 952-959

    Worldwide

    M0H91A

    HP 962-969

    Worldwide

    3JB16A

  3. Follow the online instructions to order the printhead assembly.

If the error message persists, continue to the next step.

Step 6: Service the printer

Service or replace your HP product if the issue persists after completing all the preceding steps.

Go to Contact HP Customer Support to schedule a product repair or replacement. If you are in Asia Pacific, you will be directed to a local service center in your area.

To confirm your warranty status, go to HP Product Warranty Check. Repair fees might apply for out-of-warranty products.

torreshimanxim.blogspot.com

Source: https://support.hp.com/in-en/document/c06435019

0 Response to "Hp Printer 8710 Error Continuous Ink System"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel